|
If the latest release of the new machine is the most eye-catching, then I believe that it must be glory Note10 is none. As a glory to create a two-year big-screen flagship, Glory Note 10 brings us a full range of upgrades. Familiar with this Users of the product may know: On the glory Note10, glory for the first time added liquid cooling technology to the product, so many people are very interested in the internal structure of this product. First, turn off the phone and remove the SIM card slot. Then heat the back cover of the phone, then use the suction cup to open the gap, and use the plastic cymbal to gently separate the back cover. It is worth noting: The fingerprint recognition module of Glory Note10 is and after The lids are connected together, so be careful not to break. Next, we remove the protective cover of the battery cable. Before disconnecting the motherboard, first disconnect the battery from the fuselage (right one), and disassemble the main and auxiliary board cables (middle) and the screen cable (left one) ) . Next, screw off the screw on the fuselage. At this time, you can directly take down the speaker unit in the upper right corner of the fuselage. Glory Note10's speaker module is also AAC (Audi) foundry, as described earlier, using a symmetrical design. Back to the topic, many small partners may have noticed, we forgot to remove the button cable~ Glory Note10's button cable is designed with a snap button. Next, we began to separate the protective cover of the camera area. Then cut off the connection between the rear camera cable and the motherboard, then you can remove the rear camera. This is the rear dual camera used in the glory Note10. The main camera is a 16 megapixel color lens, the secondary camera is a 24 megapixel black and white lens, and both cameras have a F/1.8 large aperture. After removing the camera area cover, we can also see the metal cover and tape used to fix the front camera. Pull the tape to see the front camera cable and disconnect it from the motherboard with a plastic pry bar. . At this time, you can remove the motherboard from the fuselage. At the same time, we can also see a part of the hot-cooled tube. The liquid-cooled tube is in contact with the main board with silicone grease. Obviously this area is used by mobile phones. The source of heat - SoC. We removed the metal cover that was attached to the top, and we can see the chip itself. The red frame area of the picture is a 6GB memory chip, and the Kirin 970 processor is packaged under the RAM. The red area in this picture is the 128GB flash memory chip of Glory Note10. After removing the motherboard, we can start the front camera. First remove the screw of the arc top cover, remove the metal cover on the front camera, and then remove the camera. Next, let's take the 'moving knife' of the sub-plate, remove the screws on the sub-board, and remove the protective cover. The speaker under the fuselage is integrated with the protective cover. Well, you can now take a photo with the two speakers! After removing the protective cover, you can see the sub-board. We found that in the Type-C interface of Glory Note10, Glory added a rubber ring to achieve dust and water resistance. Next, disassemble the connecting cable and antenna cable of the main and auxiliary boards, and then remove the sub board. Secondary board close-upNext, we removed the battery of the mobile phone: There are also instructions on the battery. First, remove the tape on both sides, then pull the middle No. 2 tape to remove the battery. At this time, the main and auxiliary board cables appear. In front of us, if you tear off the main and auxiliary board cables, you can see the screen cable below, through the opening area of the middle frame. At this time, the disassemble on the back of the fuselage has been completed. However, the liquid cooling tube of glory Note10 is still not exposed, it is not difficult to guess that it is designed between the screen and the middle frame. So we need to heat the screen, then use a metal sheet between the screen and the middle frame through a corner. Open a gap and then use a thin piece of plastic to separate the screen and the middle frame a little bit along the edge of the screen. Uncovering the graphite heat sink, the glory Note10's heat pipe is displayed in front of us. This D5 liquid cooling pipe running through the cold zone and the hot zone is 113mm in length and has the same 5mm diameter as the MacBook Air. Inside the body). Ok, finally put a glory Note10 dismantling family portrait. Overall, the interior design of glory Note10 is very reasonable and aesthetic, liquid cooling and cooling on the glory Note10's 'first show' is very amazing, enough to see, here On the glory of Note10, for the heat, it really took a lot of effort.
|
