This spring to install the new machine is not tyrants is a warrior, and I may be a martyr: 2699 Yuan msi 1066 Red Dragon to eat Chicken graphics card, a friend of the mouth of a lot of teasing me ' too extravagant ', to know that this graphics card last summer also less than 2000.
But this year to play game cut video graphics card is just needed, more than 700 pieces as soon as possible to buy some time, and finally choose a cooling appearance of the chassis.
I chose the cool Extreme Destroyer III Extreme Edition (469 yuan), standard pre-installed before 2 after 13 RGB fan, cool summer can also ensure that through the heart cool, and tempered glass side through to allow the host to the best display of light pollution.
Let's share the chassis experience with you.
Packaging more than this carton, there is a strong hardness of the thick paper frame special reinforcement, lighter than wooden racks easy to dismantle, and greatly prevent the road bumps caused by the damage to the chassis, tore off a few layers of plastic film, packaging intact. This chassis model is MB500, belongs to the Cool Extreme Destroyer series of the third generation, pre-installed three fan is the extreme version.
The size of the chassis is 494mmx211mmx475mm, the component is heavier than the general chassis, the materials are very exquisite.
Front machine armour wind, line and front face of the dust-proof network modelling is very easy to recall the destroyer of the previous generations of works, this cooler master logo nameplate reflective effect is good, can be described as the finishing touch. Host power switch, reset key and front-end USB interface are placed in the corner bevel, key or plug the device more convenient, two USB ports are 3.0 interface, after the center of the power button around can emit white light, right place a white led hard disk read and write LED.
The top has magnetic suction type dust-proof net, easy to disassemble and clear the dust. Random with two copies of paper description, a three packs of cards, a installation guide, screws, ties and light control line, such as six major accessories are hidden in the power bin of the self-contained bag.
Side plate tempered glass bottom right corner affixed with fragile warning stickers.
4mm borderless large side permeable toughened glass plate, the perspective of the very atmosphere, including chassis fan backplane, such as the internal structure at a glance, glass slightly brown, and chassis black and internal light effect can be combined with a good atmosphere.
The side plate is fixedly dependent on the lower side of the iron sheet embedded in the main groove, the upper with two screws fixed, solid and stable. The internal space of the chassis is very spacious, compatible with ATM, MicroATX, MINI-ATX motherboard, the degree of freedom is relatively high, large space can also provide a transparent heat duct.
Post 1, front 2 120mm7 leaf RGB fan close-up, fan is cool too extreme own works, you can see the production date of March 2018.
Front two fans, The bottom of the fan is rivet-type fixed, the above is a self tapping screws fixed. Here you can remove the fan to modify the cold row, support the maximum 360mm cold row, but the thickness of the upper limit of 50mm. 2 120mm fans are also DIY to 140mm specifications.
Three fans are RGB versions , so the chassis with a turn three RGB control line and power cord; In addition to a controller, you can manually control the lighting effect.
Accessories included in the Power pod, including motherboard screws, screws, ties, and fan light control lines, and so on.
Give out cool extreme one of their own power, MWE500 bronze, not modules, can provide a stable and adequate power support, good performance. First the power supply bin cover plate and the power supply back end fixed, and then from the power supply bin tail plug, with screws to complete the fixed.
The Independent power supply storehouse can guarantee the power dissipation to be free from interference, the operation is more stable.
The chassis supports a total of 2 HHD and 2 SSD hdd bits, of which SSD is affixed to the backplane fixed in the chassis.
and the HHD position and the Power warehouse shared space, the warehouse box to be pulled from the right side, and compatible with SSD installation, that is to say The chassis can be fixed up to 4 SSD at the same time.
Start the machine, directly to the old chassis motherboard +cpu+ memory migration over, tighten 6 screws fixed.
Reasonable layered space design and openings let cool, extreme destroyer three generations There is a flexible and free back line layout, to ensure that from the side through the internal pattern of the chassis neat and refreshing. Connect the chassis jumper to the motherboard, and boot. The following picture has not been properly received RGB control line, light pollution has not yet formed. After the light line, the fan is of perfect efficiency.
If the motherboard supports the RGB interface, you can control the fan light effect directly with the software. Currently configured for Asus B350-plus, Granville just xpg DDR4 2400 8gbx2, CPU is AMD Ryzen 5 2400G slightly weaker. First consider not only to open a nuclear show, later obviously did not hold back, can not be considered installed installation should not be thoughtless, especially for their own needs ambiguous when not rash.
Now that the video card is adequate for gaming and video clips, the processor can upgrade the farm for 2 generations. Look at the light effect, memory and CPU original fan without light effect, MSI GTX 1060 gaming X 6GB light effect more conspicuous.
The old driver looked at the light pollution is not enough, later on to modify and expand it. The use of three-way RGB light control can be unified to set the light effect, each color can be set to illuminated steady or breath lamp effects, and can be set to alternate colors, there are direct discoloration and breathing rotation of two forms. But the wire control operation must open the side plate;
If the motherboard supports sync light effect, direct access to the motherboard with software control, you can achieve more flexible lighting effect settings.
Summarize:
In general, the cool extreme destruction of the three generations of extreme version of the material used enough, fine workmanship, corner-bevel control area easy to operate, the internal layout is reasonable, the motherboard compatibility is good, back board line flexible, can ensure a clean and refreshing chassis layout.
4mm Tempered glass large side through and three installed RGB fan with a very pleasing to the light pollution, and can use the controller to achieve light effect control.
The front plate with a slight machine armour wind is both technology and fashion sense, Yan value aspect also commendable.
In addition, three fan wind road permeability, air intake, dust-proof nets readily available, can strengthen the host cooling dust-proof ability, and support the maximum 360mm cold row, the roof can also add two 120mm fans, even if the summer hit, the host cooling will not be worried. Cooling light pollution: Cool Extreme Destroyer III Extreme chassis experience
