Millet with fever, its own product has no unique design elements for a long period of time at first, and there is not much connection between the first few generations of mobile phones. With the maturity of its own scale and product line, millet On the mobile phone, there is finally a lot of consumers will see the impression of design inheritance in the first time, this situation is most evident in the MIX series.
The appearance of the MIX 2S was not changed so much. For example, we did not see any change in the position of the front-facing camera that we had previously guessed. However, first of all, there has been a huge improvement in the short-board camera. Long 845, this weapon, the improvement of the actual function is not too small. These advances have caused various effects on the internal structure of the mobile phone itself, we still open up to see.
At the same time, the important information is to say that the dismantling section is to cooperate with love and play, if you want to watch the video dismantling the entire process, you are welcome to visit the old driver Koala afterwards.
White exclusive version of the new machine, without use, direct opening, even Xiao Bian own snacks hurt ah, let's take a look at this design.
The front camera still stays in the lower right corner, perhaps only waiting for MIX 3 to be slightly different.
The white ceramic version is full of texture, which is incomparable with ordinary white glass. Unfortunately, this time there is no Unibody ceramic version, even if the exclusive version of the middle frame is also made of metal. There is a layer of cushion material between the screen and the middle frame. This is a more conventional design, but the PA high fiber used by millet will perform better than the normal cell phone's polycarbonate material.
The forehead portion of the tube-type micro-handset guarantees a clean and tidy appearance. Of course, if the budget is limited and you want to experience a similar design, now the old Lo's nut 3 is also an option.
The following officially began to disassemble, the first step out Cato.
There is no screw in the whole body, and the internal use of the buckle and glue is fixed. When removing, you need to pay attention to the fingerprint identification. The alignment line is closer to the edge of the mobile phone. Do not hurt the cable when you separate the adhesive and do not pull it.
After disconnection, you can see the previously mentioned cable, in addition, the main body part can directly see the wireless charging receiver coil on the back of the battery, and the upper part is the NFC function coil and the double camera module.
The wireless charging coil and the main board portion mask can be removed as a whole after the screw is removed. As seen from the back, the antenna overflow and the NFC coil are mainly connected to the main board through the contacts.
After removing the mask, the BTB connection of the fingerprint identification cable can be disconnected, and then the back cover is completely free. It can be seen that the gloss and texture are really comfortable.
Because the screws are basically through, the main board has been directly removed, and the surface has a large area of heat-dissipation graphite plaster covering. Millet's mobile phone is under the heat dissipation material is very full, red rice Note 5 is the same, compared to the old charm Blue E3, although the temperature will be a little higher, but it will do better in the excavation of the potential of the Xiaolong 636.
Then we take a look at the components on the motherboard. The dual camera module is not small, the main camera with optical image stabilization, can move in a small range to reverse compensation for slight vibration when shooting.
Scratch the surface of the grease and the heat sink to see the internal structure, high integration, the internal heat dissipation is also done very well, the same housing is more accurate opening, the heat is also more favorable.
Then turn to the sub-panel part. The removal of the sound cavity is relatively simple, but it should be noted that there is still a radio frequency line above the coquettish, basically across the entire upper half of the sound cavity.
After removing the sound cavity, the front camera and the small board can be seen. It must be said that the front camera module has a very small size. The backboard of the small board is fixed more securely. Be careful not to injure the board when it is separated.
After removing the small board, the entire dismantling is completed. We can see the main information of the battery and the material of the entire metal roll cage.
So, this dismantling will end here. If you like to demolition or see others dismantling to understand the internal structure of the machine, please pay attention to our iMobile mobile phone home, we will continue to bring you more and better digital Relevant information. As for the next phase of demolition, we are still relying on old-fashioned products to decide on interesting products.
Millet with fever, its own product has no unique design elements for a long period of time at first, and there is not much connection between the first few generations of mobile phones. With the maturity of its own scale and product line, millet On the mobile phone, there is finally a lot of consumers will see the impression of design inheritance in the first time, this situation is most evident in the MIX series.
The appearance of the MIX 2S was not changed so much. For example, we did not see any change in the position of the front-facing camera that we had previously guessed. However, first of all, there has been a huge improvement in the short-board camera. Long 845, this weapon, the improvement of the actual function is not too small. These advances have caused various effects on the internal structure of the mobile phone itself, we still open up to see.
At the same time, the important information is to say that the dismantling section is to cooperate with love and play, if you want to watch the video dismantling the entire process, you are welcome to visit the old driver Koala afterwards.
White exclusive version of the new machine, without use, direct opening, even Xiao Bian own snacks hurt ah, let's take a look at this design.
The front camera still stays in the lower right corner, perhaps only waiting for MIX 3 to be slightly different.
The white ceramic version is full of texture, which is incomparable with ordinary white glass. Unfortunately, this time there is no Unibody ceramic version. Even the exclusive version of the middle frame is made of metal. There is a buffer material between the screen and the middle frame. This is a more conventional design, but the PA high fiber used by millet will perform better than the normal cell phone's polycarbonate material.
The forehead part of the tube-type micro-handset guarantees a clean and tidy appearance. Of course, if the budget is limited and you want to experience a similar design, now the old Lo's nut 3 is also an option.
The following officially started dismantling, the first step out Cato.
There is no screw in the whole body, and the internal use of the buckle and glue is fixed. When removing, it is necessary to pay attention to the fingerprint identification. The alignment line is closer to the edge of the mobile phone. When separating the adhesive, do not injure the cable and do not pull it.
After disconnection, you can see the previously mentioned cable, in addition, the main body part can directly see the wireless charging receiver coil on the back of the battery, and the upper part is the NFC function coil and double camera module.
The wireless charging coil and the main board portion mask can be removed as a whole after the screw is removed. As seen from the back, the antenna overflow and the NFC coil are mainly connected to the main board through the contacts.
After removing the mask, the BTB connection of the fingerprint identification cable can be disconnected, and then the back cover is completely free. It can be seen that the gloss and texture are really comfortable.
Because the screws are basically through, the main board has been directly removed, and the surface has a large area of heat-dissipation graphite plaster covering. Millet's mobile phone is under the heat dissipation material is very full, red rice Note 5 is the same, compared to the old charm Blue E3, although the temperature will be a little higher, but it will do better in the excavation of the potential of the Xiaolong 636.
Then we take a look at the components on the motherboard. The dual camera module is not small, the main camera with optical image stabilization, can move in a small range to reverse compensation for slight vibration when shooting.
Scratch the surface of the grease and the heat sink to see the internal structure, high integration, the internal heat dissipation is also done very well, the same housing is more accurate opening, the heat is also more favorable.
Then turn to the sub-panel part. The removal of the sound cavity is relatively simple, but it should be noted that there is still a radio frequency line above the coquettish, basically across the entire upper half of the sound cavity.
After removing the sound cavity, the front camera and the small board can be seen. It must be said that the front camera module is really small in size. The backboard of the small board is fixed more firmly. Be careful not to injure the board when it is separated.
After removing the small board, the entire dismantling is completed. We can see the main information of the battery and the material of the entire metal roll cage.
Then the dismantling of this issue will end here. If you like to demolition something or see others dismantling to understand the internal structure of the machine, please pay attention to our iMobile mobile phone home, we will continue to bring you more and better digital Relevant information. As for the next phase of demolition, we are still relying on old-fashioned products to decide on interesting products.
