The toilet blocked is a very upset thing. How to dug the toilet blocked, I believe we have had this question. Today we come to explain to you about how the toilet blocked and the corresponding toilet installation skills. End of the article we introduced the following, we once again face the problem of toilet block can soon be solved. How to clear the toilet blocked First of all, you have to determine whether there is difficult to dissolve in hard water, such as: sanitary napkins, towels, vials, etc. If this is the case, you must find a special manager to clear the pipeline with a special machine to help The Second, if it is fecal or paper is too large lead to block the situation, then you can try this small method: Your home must be equipped with a simple toilet (ie, a round brush on one side and a string of sticks or sticks) that are sold in supermarkets and small shops. 2, prepare a bucket of water, so that the toilet with a lot of water. 3, the general water can not flow down, it is because there are objects clogged in the toilet to the sewer position between, so, after a lot of water in the toilet, you pick up a simple toilet, the round brush at the toilet The nozzle, do the piston movement (ie temporarily plug the outlet, temporarily release), the principle is: to make water in the toilet to block the impact of the formation of force.Fast, it will be smooth and unobstructed. 4, often go to the toilet inside to pour some toilet spirit, do not brush, cover the cover for more than ten minutes and then washed with water, once a few months like. 5, Mop method: Mop your home with mop.First put the mop in the mouth, and then release the water to ensure that the mop drowned.And then pressed the mop cloth, put it into the mouth as much as possible into the toilet, and finally with the fastest speed Lift the mop, repeated this action, toilet things will be sucked out of the pipe can be smooth. 6, to find a little longer plastic pipes, then tap water, plunged into the mouth of the toilet, and then the toilet mouth with rags and the like blocking, and then open the tap water, it will use water pressure to clear the pipeline. 7, if the toilet is blocked by hard objects, you can solve this.Pioneer Pizizi put the dirt aside, while the water aside hides, so that only the toilet water, and then use a towel to dry, find a small environment, the most Good is the kind of small makeup mirror, a flashlight, a small mirror on the bottom of the toilet, adjust the angle of the light source and the mirror can see part of the interior of the pipe, usually small things will be stuck in the pipe inside to be down Turn around to find a more appropriate wire, the card in the toilet noise son of small things to solve. Toilet installation tips 1, check the sewage pipes and the ground level in the installation of the toilet before the sewage pipe should be a comprehensive inspection to see if there are mud in the pipeline, waste paper and other debris blockage, and check the toilet seat before and after the level of whether the level, such as Found the ground uneven, the ground should be installed in the installation of the toilet should be used in the national standard requirements of the plastic pipe pipe wall should be smooth, smooth, no bubbles, no cracks, no obvious signs and sags. To ensure that the sewage pipe above the ground about 10mm. 2, to determine the sewage pipe center. Turn the toilet over, in the toilet to determine the sewage outfall center, and draw the cross center line, the center line should be extended to the bottom of the toilet around the feet. 3, fixed the toilet to determine the bottom of the toilet installation of the bottom of the screw position, drill hole with electric drill and embedded plastic sleeve expansion screw will be on the toilet with the crosshair of the sewage outfall alignment, to maintain the level of installation of toilet , And force the seal ring, install the ground screws and decorative cap. 4, do a good job at the bottom of the seal in the toilet sewage outfall to install a special seal, or in the sewage pipe around the circle marked with plastic (putty) or cement mortar, cement and sand ratio of 1: 3 toilet installation to maintain Level. 5, Install the water tank fittings. Put on the water for 3-5 minutes to flush the pipes to ensure the cleanliness of the water pipes. Then install the angle valve and the connecting hose, connect the hose to the water inlet valve of the water tank fittings and press the water source. 6, commissioning test. After installation connected to the water, check the inlet valve water and sealing is normal, check the drainage valve and installation location are corresponding to each other, whether the installation is tight, with or without leakage, check the length of the button switch chain is appropriate Whether it is flexible, there is no chance to jam, check whether the missing water inlet valve filter device. 7, waiting for curing. The toilet after the installation should wait until the glass glue or cement mortar can be used after curing. After installation for three days can not be used to the current cement solidification rate at least one day to use, so as not to affect its stability. The toilet plug how to clear and toilet installation skills is a very practical knowledge in the day, we can share to friends around and can be, to prepare for contingencies.If the uncle for the toilet block or install there are more want to know Knowledge, you can focus on our website, we will update from time to time for everyone. |
